Glemt adgangskode?
Opret konto

Phihong POE21-120F PoE fordeler - 21 Watt

Producent Phihong
Produkt nr. POE21-120F
Varenummer 973257
860,- DKK
Lagerstatus:
  0 stk. København
  0 stk. Aarhus
  0 stk. Fjernlager
Forventet levering ved bestilling: 08/07/2017
Mere info
Produktbeskrivelse Phihong POE21-120F - PoE fordeler - 21 Watt
Enhedstype PoE fordeler - ekstern
Vægt 200 g
Udgangspænding 12 V
Strømkapacitet 21 Watt
Input-stik RJ-45
Output-stikforbindelser 1 x RJ-45
Netværk Ethernet 10/100/1000
Dimensioner (B x D x H) 5.6 cm x 10 cm x 2.8 cm
Enhedstype PoE fordeler - ekstern
Indgangspændingsområde DC 45 - 57 V
Input-stik RJ-45
Detaljer om strømudgangskonnektorer 1 x RJ-45
Udgangspænding 12 V
Strømkapacitet 21 Watt
Grænseflade til fjernstyring Ethernet 10/100/1000
Rackmonteringspakke Inkluderet
Egenskaber Beskyttelse mod overophedning, LED-indikatorer, beskyttelse mod overstrøm, overspændingsbeskyttelse, overbelastningsbeskyttelse
Overensstemmelsesstandarder EN55022 Klasse A, EN 61000-4-2, EN 61000-4-3, EN 61000-4-6, FCC Part 15 A
Min. driftstemperatur 0 °C
Maks. driftstemperatur 40 °C
Fugtighedsgrad ved brug 5 - 90%
Bredde 5.6 cm
Dybde 10 cm
Højde 2.8 cm
Vægt 200 g

Most devices on the market now designed to operate on a network will be compliant with the IEEE802.3af standard; however users who are upgrading their network do not necessarily need to upgrade their accessory devices. The dilemma comes as what to do with all of this non-PoE equipment after installing a PoE network. Phihong has a solution with the POE21-120F. The POE21-120F is a small device that will connect to the network and split the power into 21W over a DC cable and 30W of continued PoE to the device. This unique device takes ultra or mega PoE (60W or greater) and splits the power to end devices that might required an accessory device for example as a pan/tilt/zoom camera and a heater or illuminator.
Using standard Category 5 or above Ethernet cables, the POE21 will take its power from the Ultra or Mega PoE midspan/power injector or its equivalent. The device will then split the PoE into a 21W, 12V DC cable to the accessory device and the remaining 30W of power and data will run separately on the output Ethernet cable. The POE21-120F comes in a standard output voltage of 12VDC so users need to be aware that it cannot be higher or lower than their device's power requirements. The diagram above shows the basic set up of a POE21-120F Splitter connected to a PoE camera and a choice of non-PoE ready devices.
The POE21-120F is connected to the network switch through an ultra PoE power injector (60W), then splitting the power into the two outputs allowing for both devices to be powered from a single Ethernet cable. The end device may be placed up to 100 meters from the network switch using this set-up.

Finansiering
Læs vilkår
Løbetid
Pr. måned KUN
ÅOP 9000.1%
Låneomkostninger
Finansiering vælges som betalings metode når du gennemfører din bestilling. Papirløs godkendelse med NemID.